This post comes with the guide to repair BMW FRM Module using xprog box programmer. Connect 9(S)12 BDM adapter to XPROG programmer, then weld all lines incl. VDD (+5V), RESET, GND, BKGD on adapter to the corresponding position on BMW FRM module Run Xprog software (here used is v5.6.0) Click “ Continue Reading →
Here, have collected the solutions for software operation problems from Xprog-M box ECU programmer users. 1.Problem: The xprog V5.84 shows “Access violation at address 00478FC6 in module “XProgDesktop.dll”. Read of address 00000358.” Solution: Check if the anti-virus software has been inst Continue Reading →
New XPROG V6.12 adds new authorization: AUTH-0028-3 Renesas RL78 Authorized and AUTH-0028-4 Renesas M32C Authorized. With USB Dongle and new generation hardware, it doesn’t need to activate and can run more steady and faster than old version. XPROG-M V6.12 Free Download Link 1: https Continue Reading →
Look here: what eeprom is covered by Xprog 6.12 programmer? Atmel AT24C01A AT24C02 AT24C04 AT24C08 AT24C16 AT24C32 AT24C32A AT24C64 AT24C64A AT25010 AT25020 AT25040 AT25080 AT25160 AT25320 AT25640 AT25128 AT25256 AT93C46 AT93C46A AT93C56 AT93C56A AT93C57 AT93C66 AT93C66A C Continue Reading →
Offer free download Xprog 5.8.4, xprog 5.74, xprog 5.55, xprog 5.51 from mega, no password and the authorization is complete. xprog 5.74 free download Link 1: https://mega.nz/#!PQUzGAKI!LuBfkREVI9vnjPtPKlhdjbv6welC8GkHoZM4Bm9wois 46.6 MB Link 2 https://mega.nz/#!vUknWAaZ!VwXXnaREXg Continue Reading →
First comes the free download link of Xprog M 5.5.5 flash files https://mega.nz/#!kcJzHKiI!oODgrezoNa22lTLVo4Fc3_5QL3FQQ0yzRqVDc5a_FV0 Guide: In xprog choose atmega64 >>> PROJECT >> FILES, and load FLASH, EEPROM and CONFIGURATION files >> Firts ERASE DEVICE… afte Continue Reading →
2018 Xprog M V5.84 firmware V4.4, with USB dongle, adds new authorizations: AUTH-0028-1 Renesas V850 Authorized and AUTH-0028-2 Renesas SuperH Authorized 2017/10/9. XPROG-M V5.84 Authorizations: AUTH-0001 Motorola HC05 family authorization (allows to read/write EEPROM) AUTH-0002 Continue Reading →
I’d like to show you how to read EWS3 0D46J from BMW E39 using a Xprog-M programmer. The EWS 3 Immobilizer unit , in the BMW E39 car body, is above the pedals, on the left. remove it. take the board out of the case. The immobilizer is assembled on a Motorola microcontroller with a m Continue Reading →
Verified: VVDI Prog can’t read Mercedes-Benz W210 EIS 68HC05. That is because W210 eis 68hc05 inside. 2 piece. and Vvdi prog does not know about 68hc05. Only hc908 and hc912 it has been ignored due to the fact that many other early programmers can do, such as Xprog-m or Orange5 or ETL, Continue Reading →
